← All guides

Guide · Safety and WHS

Welding fume exposure limits in Australia: what fab shops need to do

Welding fume is one of the biggest health risks in a fabrication shop, and the legal limit dropped sharply in 2024. Here is what the current limit means on the floor, what changes from 1 December 2026, and how to show you are in control.

By the Manufacturing Growth Hub team · Updated 15 November 2026

The short answer: the exposure standard for general welding fumes in Australia is 1 mg/m³ averaged over an eight-hour shift, down from 5 mg/m³, and aluminium welding fumes have been cut to the same figure. In practice, most shops can't stay under that limit with general shed ventilation alone. You need fume captured at the source, air monitoring wherever you're unsure, and respirators only as the last line of defence.

What the limit is and when it changed

Safe Work Australia sets the exposure standards for airborne contaminants, and each state and territory regulator gives them legal force. For welding fumes not otherwise classified, the standard is now 1 mg/m³ as an eight-hour time-weighted average (TWA), measured in the welder's breathing zone and based on a five-day week. The old figure was 5 mg/m³.

In Victoria, WorkSafe says the reduced standard took effect on 18 January 2024. Other jurisdictions adopted it on their own timetables, so if you operate interstate, check with the local regulator.

WHS ministers later agreed to cut the standard for aluminium welding fumes from 5 mg/m³ to 1 mg/m³ as well, bringing it into line with general welding fumes. Again, each regulator sets the date it becomes enforceable.

The reason for the change is serious. In 2017 the International Agency for Research on Cancer (IARC) moved welding fumes to Group 1, carcinogenic to humans. WorkSafe Victoria lists lung and kidney cancer among the possible health effects.

An exposure standard is a ceiling, not a target. Under both the Victorian OHS laws and the model WHS laws, you still have to eliminate or reduce the risk so far as reasonably practicable, even if you're already under the number.

What changes on 1 December 2026: WES becomes WEL

From 1 December 2026, the Workplace Exposure Standards (WES) are replaced by Workplace Exposure Limits (WEL). Safe Work Australia says the new name makes clear these are limits that should not be exceeded. Most values are unchanged, but some go down, some go up, and some substances are added or removed. Until 30 November 2026 the current WES list still applies.

Two parts of the change matter in a fab shop:

  • Chromium VI compounds have no numeric limit from 1 December 2026. They're treated as non-threshold genotoxic carcinogens, so there is no "safe" number to stay under. You must eliminate the exposure where reasonably practicable, or otherwise minimise it as far as reasonably practicable. Chromium VI is formed when welding stainless steel and other chromium-bearing materials.
  • Manganese is one of the substances with a transition period. WorkSafe Victoria lists manganese (fume, dust and compounds) among 15 substances that have until 2029 to move to their new limits. Manganese is present in most steel welding fume, so use the transition period to review your controls.

We haven't seen anything confirming a further change to the 1 mg/m³ figure for welding fumes under the WEL list. Check the published WEL list or your regulator for the value that applies on the day.

Fume components can have lower limits

The 1 mg/m³ figure covers the fume as a whole. Individual metals in that fume have their own limits, and some are much lower. WorkSafe Victoria warns that even when you meet the general standard, you should still keep exposure to each component as low as you can. As a rough guide to what's in the fume, by material:

Material or processComponents to look at
Mild and structural steelIron oxide, manganese
Stainless steelChromium (including chromium VI), nickel, manganese
Galvanised steelZinc oxide, plus anything in the coating
AluminiumAluminium welding fumes, ozone
Painted or primed steelLead, cadmium or other coating chemicals, depending on the paint

Check the safety data sheets for your consumables and base metals. Suppliers have a duty to give you that information.

Controls that actually work, in order

WorkSafe Victoria sets out the controls in this order: change the process first, then ventilation, then respiratory protection. Here's what that looks like on a shop floor.

1. Change the process

  • Design out welding where you can, for example by using bolted connections or bought-in components.
  • Choose lower-fume processes. MIG or TIG generally produce less fume than stick (MMAW) or flux-cored (FCAW), and pulsed MIG and waveform-controlled processes help too.
  • Use argon-rich shielding gas instead of CO2-rich mixes, and keep current no higher than the job needs.
  • Grind off paint, primer and galvanising before welding, position the work so the welder isn't leaning over the plume, and keep people who aren't welding away from the area.

2. Capture the fume at the source

  • On-torch extraction captures fume right at the arc. It's less effective for overhead and vertical work.
  • Local exhaust ventilation (LEV), such as downdraft tables, side-draft booths and fixed or portable hoods, suits repetitive work on small to medium items.
  • Dilution fans should rarely be your only control. If you use them, put them to the side of the welder to create a cross-draught, not behind or in front. Natural ventilation through open roller doors is unreliable.

Look after the LEV once it's in. Under the Victorian OHS Regulations, control measures have to be properly installed, used and maintained.

3. Respiratory protection as the last line

  • Use RPE only where higher controls aren't practicable, or as a top-up or interim measure. It protects only the person wearing it.
  • Respirators must meet AS/NZS 1716:2012 or an equivalent standard. Powered air-purifying respirators (PAPRs) give the highest protection, followed by half-face P2/P3 cartridges and then P2 disposables. P1 disposables aren't suitable for welding fume.
  • Half-face respirators only seal on a clean-shaven face. Fit, training and maintenance are your responsibility, and masks must not be shared.

Air monitoring and health monitoring

In Victoria, regulation 166 of the OHS Regulations 2017 requires atmospheric monitoring if there's reasonable doubt about whether the exposure standard is being exceeded, or if monitoring is needed to work out the health risk. Welding work is often intermittent and varies a lot, so that doubt is common. You can either monitor or put in controls strong enough to remove the doubt.

  • Personal monitoring is done inside the welding helmet by a competent person, such as an occupational hygienist. It's the only type of result you can compare directly with the exposure standard.
  • Static monitoring shows fume levels across an area, which helps protect nearby workers.
  • Keep the results, with the process, controls in use, and how long and how often people were exposed. Regulations 168 and 171 require records of air and health monitoring.

Health monitoring is required where workers are exposed to specified substances and that exposure is reasonably likely to affect their health. For welding, WorkSafe Victoria points to inorganic compounds of cadmium, chromium and lead, particularly where you rely heavily on respirators or administrative controls. Talk to an occupational physician about what's needed.

Outside Victoria, the model WHS Regulations and Safe Work Australia's model Code of Practice: Welding processes set out similar duties. Also remember you must consult your workers and any health and safety representatives about the hazards, the controls and the monitoring results.

A simple plan for the next month

  1. List every welding process, base metal, coating and consumable you use, and collect the safety data sheets.
  2. Walk the floor and record what controls each bay actually has: extraction, LEV, fans, RPE.
  3. Where you're not sure exposure is under the limit, book personal air monitoring with an occupational hygienist.
  4. Fix the gaps in order: process changes first, then capture at the source, then RPE with fit testing.
  5. Check your stainless and manganese exposure against the WEL changes from 1 December 2026.
  6. Write it into your risk assessment and SWMS, run a toolbox talk, and set a date to review it.

How we help

CompliHub is the safety, HR and ISO side of the MGH App. You can keep your welding hazards and risk assessments, SWMS, training records, toolbox talks and consultation records in one place, so the evidence is there when a WorkSafe inspector or an ISO 45001 auditor asks. CompliHub doesn't measure fume or replace an occupational hygienist. It keeps the plan and the proof organised. Unlimited users are included, so your whole floor can sign onto SWMS and toolbox talks.

This guide is a plain-English summary for Australian fabricators, based on published guidance from Safe Work Australia and WorkSafe Victoria as at November 2026. It is not legal advice. Check the current exposure limits list and your state or territory regulator, and get an occupational hygienist's advice for your own shop.

Common questions

What is the welding fume exposure limit in Australia?

The workplace exposure standard for welding fumes not otherwise classified is 1 mg/m³ as an eight-hour time-weighted average, reduced from 5 mg/m³. Aluminium welding fumes have also been reduced to 1 mg/m³. Each state and territory regulator sets when the change is enforceable.

Do I have to do air monitoring for welding fumes?

You must monitor if there is reasonable uncertainty about whether workers are exposed above the limit, or if monitoring is needed to work out the health risk. Because welding work is often variable, many shops need personal monitoring by a competent person such as an occupational hygienist.

Is a fan or open roller door enough to control welding fume?

Usually not. WorkSafe Victoria says dilution fans should rarely be the only control and natural ventilation is unreliable. Capture at the source, such as on-torch extraction or local exhaust ventilation, comes first, with respirators as the last line of defence.

Sources

Want help with this in your shop?

Talk to a team that works with Australian fabricators every week.